Introducing NovoPlast
A ground breaking Cement-Free 3-in-1 Colored plaster solution
About NovoPlast
The innovative formulation ensures a low carbon footprint, with no water required at any stage, as it cures in ambient air. NovoPlast not only conserves resources and energy but also promotes greener building practices.
Features
Cement & riversand free colored plaster
Fast drying and curing in ambient air, with no water required
Thin coating compared to conventional coatings
Eliminates the need for primer and paint
Reduces time and labor compared to traditional methods
Available in a variety of shades

Benefits
01
02
03
04
05
06
07
08
09
10
Experience efficient and sustainable plastering with NovoPlast
More information about Novoplast
NovoPlast – Cement-Free Coloured Ready-Mix Plaster
A Smarter 3-in-1 Solution for Wall Plastering and Finishing
Construction finishing involves several stages. After the basic masonry work, conventional wall finishing generally requires plastering, primer application and painting. Each stage requires additional material, labour and working time. The surface also needs to be prepared before the next operation can begin.
NovoPlast by Novota Thermotech Pvt. Ltd. offers a different approach.
NovoPlast is a dry, ready-mix coloured plaster containing quartz sand with predetermined grain sizes to provide good particle packing. It can be applied on brickwork, cement blocks and concrete surfaces in place of conventional cement-sand plaster.
Once applied, NovoPlast sets into a hard coating that adheres strongly to brick and other mineral substrates. It is available in different colour shades, eliminating the need for a separate primer and painting process.
The product combines plastering, surface finishing and colour in one application. According to the product specifications, this 3-in-1 solution can reduce the overall start-to-finish duration from approximately 3–4 weeks to around 1 week, while saving the additional time and cost associated with primer and painting.
For builders, contractors, developers and construction professionals, NovoPlast provides an alternative way to approach wall finishing with fewer conventional finishing stages.
What Is NovoPlast?
NovoPlast is a dry ready-mix plaster developed for application on mineral construction surfaces such as bricks, cement blocks and concrete.
Its formulation contains quartz sand with predetermined grain sizes. This controlled particle sizing provides good packing of the plaster ingredients and contributes to a smooth finishing texture.
Unlike conventional cement-sand plastering followed by separate primer and painting operations, NovoPlast is supplied in different colours. The coloured plaster provides the finished surface without requiring an additional painting stage.
The material is supplied in 40 kg bags. For application, the dry mix is combined with an activator solution prepared using the activator supplied in a pouch and soft water. The prepared mortar is then applied using a masonry trowel and levelled using a flat hand-held trowel.
NovoPlast is designed to form a hard coating with strong adhesion to suitable mineral substrates. It cures in ambient air and does not require water during the curing process.
In practical terms, NovoPlast brings three conventional finishing requirements together:
Plastering: Provides the plaster layer on the prepared mineral substrate.
Surface finishing: Provides a smooth finishing texture through its predetermined particle-size packing.
Colour: Is available in different shades, eliminating the need for separate painting.
This makes NovoPlast a practical alternative for projects looking to simplify the conventional plastering and finishing sequence.
Why Choose NovoPlast?
1. Three Finishing Requirements in One Product
Conventional finishing generally involves plastering, primer application and painting. These are separate operations that require their own materials, labour and working time.
NovoPlast combines these requirements into one coloured plaster solution.
The product is designed to replace conventional ready-mix plastering, primer and painting work. Since it is available in different colours, the finished surface does not require an additional primer and painting process as described in the product brochure.
For construction projects, reducing separate operations can simplify planning and coordination between different work stages.
2. Reduces Overall Project Finishing Time
Time is an important consideration in construction. Every additional finishing stage affects the project schedule, labour planning and availability of the work area.
NovoPlast is designed to reduce the total start-to-end duration of the conventional plastering and finishing process.
According to the product information, the overall duration can be reduced from approximately 3–4 weeks to around 1 week.
This benefit comes from combining plastering, finishing and colour into one product rather than following separate plastering, primer and painting operations.
For builders and contractors, a shorter finishing schedule can make it easier to plan subsequent construction activities and complete wall-finishing work within a shorter period.
Actual project duration will depend on site conditions, surface preparation, application planning and the work schedule.
3. No Separate Primer and Painting Required
NovoPlast is supplied in different colour shades. This eliminates the need for separate painting work as described in the product brochure.
The product also eliminates the need for primer as part of the conventional finishing sequence it replaces.
This reduces the number of finishing materials required and avoids separate primer and painting operations.
For projects where large wall areas need to be finished, reducing these additional stages can simplify material procurement, labour coordination and work scheduling.
4. Cement-Free Formulation
NovoPlast is a cement-free coloured plaster.
The product also uses quartz sand with predetermined grain sizes and does not use river sand, according to its product specifications.
Its formulation is intended to provide good particle packing and a smooth finishing texture.
For construction professionals evaluating alternatives to conventional cement-sand plaster, NovoPlast offers a different material and application approach.
5. Smooth Finishing Texture
The quality of a finished wall depends on the material formulation and the application process.
NovoPlast uses predetermined particle sizes to provide enhanced packing of the plaster ingredients. This contributes to a smooth finishing texture.
The material is applied as a mortar and levelled with a flat hand-held trowel.
The controlled particle-size packing is also intended to minimise cracks in the structure.
The final finish depends on suitable surface preparation, correct mixing and proper application.
6. Strong Adhesion to Mineral Substrates
NovoPlast is designed to adhere strongly to brick and other mineral substrates.
The product description identifies brick, cement blocks and concrete as suitable surfaces for application.
Good substrate adhesion is important for a plaster coating because the material needs to remain firmly attached to the surface after application and setting.
For this reason, the surface must be clean, dry and sound before application. Loose material, algae, powder and unstable non-mineral coatings must be removed or repaired.
Following the specified surface-preparation and application instructions helps achieve the intended bond with the substrate.
7. Hard Coating After Setting
After application, NovoPlast sets into a very hard coating.
The technical information provides compressive strength and flexural strength values at different curing ages. These values offer useful information for engineers, contractors and construction professionals evaluating the product.
The specified compressive strength is:
1 day: 14.5 N/mm²
3 days: 19.4 N/mm²
7 days: 21.6 N/mm²
The specified flexural strength is:
1 day: 3.6 N/mm²
3 days: 4.5 N/mm²
7 days: 5.2 N/mm²
These figures are provided in the product’s technical data. They should be considered in accordance with the stated test references and product specifications.
8. Air Curing Without Water
NovoPlast cures in ambient air and does not require water at any stage during curing.
This is an important difference in the curing procedure compared with materials that require water curing.
After application, the product must be allowed to air cure for 24 hours. Water must not be splashed on the applied material.
The product information also specifies fast dry curing in 2 days and 100% curing in 5 days.
The application must be protected from rain during the curing period.
For site teams, following these instructions is important. The curing process should not be treated like conventional water-curing work.
9. Reduced Application Wastage
Material wastage affects the overall cost and efficiency of construction work.
NovoPlast is designed to minimise rebound loss during application, thereby reducing material wastage.
The product also provides a cohesive, workable mortar when prepared according to the specified mixing procedure.
Reduced rebound loss can help make application more efficient and support better utilisation of the material at the work site.
Actual consumption and wastage will depend on the substrate, application thickness, surface condition and workmanship.
10. Resistance and Protection Features
NovoPlast’s listed advantages include:
High resistance to UV degradation.
Acid rain resistance.
Antifungal properties.
Prevention of water absorption.
These features are part of the product’s stated performance characteristics.
They make the product relevant for construction applications where the specified surface-protection properties are important.
The product should still be applied according to the recommended procedure and used on suitable substrates.
11. Eco-Friendly Product Positioning
The NovoPlast brochure identifies the product as eco-friendly with a low carbon footprint.
It is also a cement-free coloured plaster and does not use river sand.
The product’s ability to combine plastering, primer and painting work into a single solution can reduce the number of separate finishing materials and operations required.
These are relevant considerations for construction professionals evaluating material choices and finishing processes.
How NovoPlast Improves the Conventional Plastering Process
Conventional wall finishing generally involves multiple operations.
First, the wall is plastered. After the plastering work, the surface needs to be ready for subsequent finishing. Primer is then applied, followed by painting.
Each stage requires separate work planning, material handling and labour.
NovoPlast changes this sequence by providing a coloured plaster that performs the plastering and finishing function in one application.
Conventional Finishing Approach
Conventional plastering.
Surface preparation for the next stage.
Primer application.
Painting.
Additional material and labour coordination.
NovoPlast Approach
Prepare the mineral substrate.
Mix NovoPlast with the specified activator solution.
Apply the mortar.
Level the surface.
Allow the material to air cure.
Since NovoPlast is available in different colour shades, separate primer and painting work is eliminated as described in the product brochure.
The brochure indicates that this approach can reduce the overall start-to-finish duration from approximately 3–4 weeks to around 1 week.
The exact time required for a project will depend on its size, site conditions, surface preparation and application schedule.
Areas of Application
NovoPlast is intended for application on suitable mineral construction surfaces.
The product brochure identifies the following areas:
Wall Plaster
NovoPlast can be applied as a coloured plaster on suitable wall surfaces, including brickwork and cement blocks.
It provides a hard coating with a finishing texture and eliminates the need for separate painting.
Ceiling Surfaces
The product is listed for application on ceiling surfaces.
As with other applications, the substrate must be sound and properly prepared before the material is applied.
Concrete Surfaces
Concrete is identified as a suitable mineral substrate for NovoPlast.
The surface must be clean, dry and free from loose material, algae and powder before application.
Substrates
NovoPlast is designed for brick and other mineral substrates.
The suitability of a particular surface should be checked before application, especially where previous coatings or repairs are present.
Sidewalks
Sidewalks are also listed among the product’s areas of application.
The application should follow the product’s surface-preparation and installation requirements.
NovoPlast Application Procedure
Correct mixing and application are important for achieving the intended performance of any construction material.
NovoPlast is supplied as a dry mix and requires preparation with the activator solution before application.
The following procedure is based on the product brochure.
Step 1: Prepare the Activator Solution
Dissolve the activator supplied in the pouch into soft water.
The specified water quantity is approximately 6.4 to 6.5 litres for each 40 kg bag.
Use the specified quantity when preparing the solution.
Step 2: Mix the Dry Material
Mix the dry NovoPlast material for approximately 4–5 minutes.
A mechanical mixer should be used to achieve a homogeneous mix.
Proper mixing helps distribute the ingredients uniformly.
Step 3: Add the Activator Solution
While continuously stirring the dry mix, gradually add the prepared activator solution.
Continue stirring for approximately 5 minutes.
The objective is to obtain a uniform mixture suitable for application.
Step 4: Prepare the Mortar
After mixing, the wet material is ready for use.
The prepared mortar should be applied within its specified working period.
Step 5: Prepare the Substrate
Saturate the substrate with water to prevent it from absorbing water from the mixed material.
The substrate must be clean, dry and sound before application, with unstable coatings and loose material removed or repaired.
Follow the specified substrate-preparation instructions.
Step 6: Apply the Material
Apply NovoPlast using a masonry trowel.
The product has a pot life of approximately one hour, during which the prepared mortar must be applied.
Step 7: Level the Surface
After application, level the surface using a flat hand-held trowel.
The recommended application thickness is between 5 mm and 10 mm.
Ensure that the material is applied consistently across the required area.
Curing Instructions
NovoPlast cures in ambient air.
It does not require water during the curing process.
The following instructions must be followed:
Allow the applied material to air cure for 24 hours.
Do not splash water on the applied surface.
Protect the application from rain during the curing period.
Follow the product’s stated curing information.
The brochure specifies fast dry curing in 2 days and 100% curing in 5 days.
The technical data separately specifies an initial set of approximately 3 hours and a final set of approximately 5 hours.
Setting and curing are different stages, so these figures should be read according to their respective meanings.
Technical Data of NovoPlast
The following technical details are based on the product brochure.
| Particulars | NovoPlast Specification |
|---|---|
| Product form | Dry ready-mix plaster |
| Appearance and colour | Available in different colour shades |
| Water-to-powder ratio | 0.16 |
| Dry density | 1483 kg/m³ |
| Wet density | 2258 kg/m³ |
| Workability (initial flow) | 166 mm |
| Workable life | 115 minutes |
| Initial set | Minimum 3 hours |
| Final set | Minimum 5 hours |
| Application thickness | 5–10 mm |
| Consumption | Approximately 1.7 m² per 40 kg bag at 10 mm thickness |
| Packing | 40 kg bags |
| Shelf life | 6 months from manufacture in original unopened bags, when stored in dry conditions |
Compressive Strength
| Curing Age | Strength |
|---|---|
| 1 day | 14.5 N/mm² |
| 3 days | 19.4 N/mm² |
| 7 days | 21.6 N/mm² |
Reference: BS EN 1015-11:1999.
Flexural Strength
| Curing Age | Strength |
|---|---|
| 1 day | 3.6 N/mm² |
| 3 days | 4.5 N/mm² |
| 7 days | 5.2 N/mm² |
Reference: IS 4031 Part 8:1988.
Other Test References
Dry density: IS 2542 Part 1 (RA 2017).
Wet density: IS 1199 Part 3.
Workability and workable life: BS EN 1015-3:1999.
These values are the technical specifications stated in the product brochure.
Material Consumption and Packing
NovoPlast is supplied in 40 kg bags.
The approximate consumption is:
1.7 square metres per 40 kg bag at 10 mm thickness.
This is an approximate consumption figure. Actual material requirements can vary depending on the surface condition, application thickness and workmanship.
For project estimation, the required quantity should be calculated using the actual area and intended application thickness.
Storage and Shelf Life
The product has a shelf life of 6 months from the date of manufacture when stored in its original unopened bags under dry conditions.
Bags should be stored in a dry location and protected from moisture.
Why NovoPlast from Novota Thermotech?
Choosing a construction finishing material involves more than looking at its colour or appearance. Contractors, builders and project engineers need to understand the material, its application requirements, technical specifications and the work process it is intended to replace.
NovoPlast from Novota Thermotech is developed around a clear construction requirement: simplify wall plastering and finishing by combining plastering, surface finishing and colour in one product.
Its product formulation uses quartz sand with predetermined grain sizes to provide good particle packing. It is supplied as a dry ready-mix material and prepared using the specified activator solution.
The product is designed to provide a hard coating with strong adhesion to suitable mineral substrates.
Its different colour options eliminate the need for separate painting. The product also eliminates the need for primer as part of the conventional finishing sequence it replaces.
A Product Designed Around Practical Site Requirements
NovoPlast offers several practical advantages for construction work:
One coloured plaster solution instead of separate plastering, primer and painting operations.
Reduced overall finishing time, with the brochure indicating a reduction from approximately 3–4 weeks to around 1 week.
No separate painting required.
No separate primer required.
Cement-free formulation.
No river sand.
Smooth finishing texture through predetermined particle-size packing.
Strong adhesion to suitable mineral substrates.
Air curing without water during the curing process.
Reduced rebound loss during application.
Different colour options.
Technical strength values provided in the product specifications.
These features give builders, contractors and construction professionals a clear basis for evaluating NovoPlast as an alternative to conventional finishing methods.
Engineering-Based Product Information
Novota Thermotech provides product information covering material preparation, application, curing, consumption, storage and technical properties.
For engineers and contractors, this information is important because the performance of a construction material depends not only on its formulation but also on correct site preparation and application.
NovoPlast’s brochure specifies the mixing procedure, water quantity, working life, application thickness, curing instructions and strength values.
Following these instructions helps ensure that the material is used in accordance with its intended application.
Novota’s approach is to present the product through its stated technical characteristics and practical application requirements, enabling construction professionals to assess its suitability for their projects.
Important Application Precautions
NovoPlast is an alkaline product. Care should be taken to avoid contact with the eyes, skin, mouth and food.
If the material splashes onto the body, wash the affected area with plenty of water.
Additional application precautions include:
Ensure the substrate is clean, dry and sound before application.
Remove algae, powder and loose material.
Remove or completely repair unstable non-mineral coatings such as traditional paint.
Use soft water and the specified quantity for preparing the activator solution.
Use a mechanical mixer to obtain a homogeneous mixture.
Apply the prepared mortar within its specified pot life.
Maintain the recommended application thickness of 5–10 mm.
Do not splash water on the material during curing.
Protect the applied material from rain during the curing period.
Store unopened bags in dry conditions.
Correct preparation and application are essential for obtaining the intended product performance.
Frequently Asked Questions About NovoPlast
1. What is NovoPlast?
NovoPlast is a cement-free, dry ready-mix coloured plaster containing quartz sand with predetermined grain sizes. It is designed for application on brick, cement blocks and concrete in place of conventional cement-sand plaster.
2. What makes NovoPlast different from conventional plaster?
NovoPlast combines plastering, surface finishing and colour in one product. It is available in different colour shades and eliminates the need for separate primer and painting work as described in the product brochure.
3. Does NovoPlast require painting?
No. NovoPlast is available in different colours, eliminating the need for separate painting.
4. Is a primer required before painting or finishing?
NovoPlast is designed as a 3-in-1 solution that replaces conventional ready-mix plastering, primer and painting work. Separate primer application is not required as part of the finishing sequence it replaces.
5. On which surfaces can NovoPlast be applied?
The product is suitable for brick, cement blocks and concrete. Its listed application areas also include wall plaster, ceiling surfaces, concrete substrates and sidewalks. The surface must meet the specified preparation requirements.
6. What is the recommended application thickness?
The recommended application thickness is between 5 mm and 10 mm.
7. How much water is required for mixing?
Approximately 6.4 to 6.5 litres of soft water is required for each 40 kg bag to prepare the activator solution using the supplied activator pouch.
8. How should NovoPlast be mixed?
First, mix the dry material mechanically for 4–5 minutes. Prepare the activator solution separately. Add this solution to the dry mix while continuously stirring for approximately 5 minutes.
9. How long is the prepared material workable?
The product’s technical data specifies a workable life of 115 minutes. The application instructions separately state that the prepared mortar has a pot life of about one hour. For site application, follow the application instructions and use the prepared mortar within the specified pot life.
10. Does NovoPlast require water curing?
No. NovoPlast cures in ambient air and does not require water during curing. Do not splash water on the applied surface.
11. How long does NovoPlast take to cure?
The brochure specifies 24 hours of air curing, fast dry curing in 2 days and 100% curing in 5 days. It also specifies an initial set of approximately 3 hours and a final set of approximately 5 hours.
12. What is the approximate material consumption?
The approximate consumption is 1.7 square metres per 40 kg bag at 10 mm thickness. Actual consumption may vary with surface condition and application thickness.
13. Is NovoPlast available in different colours?
Yes. NovoPlast is available in different colour shades, eliminating the need for separate painting.
14. What is the shelf life of NovoPlast?
The shelf life is 6 months from the date of manufacture when stored in original unopened bags under dry conditions.
15. What are the main advantages of NovoPlast?
Its main advantages include cement-free coloured plaster, no river sand, no separate primer or painting, reduced finishing time, smooth finishing texture, strong substrate adhesion, air curing without water, reduced rebound loss, UV degradation resistance, acid rain resistance and antifungal properties.
Simplify Your Wall Finishing Process with NovoPlast
Conventional wall finishing involves multiple stages, materials and operations. NovoPlast offers an alternative by combining plastering, surface finishing and colour in one ready-mix product.
With its cement-free formulation, predetermined quartz sand particle sizes, different colour options, specified technical strength values and air-curing process, NovoPlast is designed for practical construction applications.
For builders, contractors, developers and construction professionals looking to simplify the plastering and finishing process, NovoPlast from Novota Thermotech is a product worth evaluating.
Reduce finishing stages. Simplify application. Choose NovoPlast.
Contact Novota Thermotech Pvt. Ltd.
For product information, technical specifications and application-related enquiries:
Novota Thermotech Pvt. Ltd.
103, Building No. 2, New Rajashree Industrial Premises CHSL,
Opp. Hyde Park, Chitalsar-Manpada,
Thane – 400610, Maharashtra, India.
Website: www.novota.in
Email: info@novota.in
Phone: +91 8104658985
Subscribe us on Linkedin
FAQs
Can the color of the plaster solution be customized to match specific preferences or design requirements?
Sed rhoncus facilisis purus, at accumsan simply free text available purus sagittis vitae. Nullam acelit at eros imperdiet. Pellentesque sit.
Is the 3-in-1 colored plaster solution suitable for both interior and exterior applications?
Sed rhoncus facilisis purus, at accumsan simply free text available purus sagittis vitae. Nullam acelit at eros imperdiet. Pellentesque sit.
What surfaces or materials can the 3-in-1 colored plaster solution be applied to?
Sed rhoncus facilisis purus, at accumsan simply free text available purus sagittis vitae. Nullam acelit at eros imperdiet. Pellentesque sit.
Are there any special application techniques or considerations when using the 3-in-1 colored plaster solution?
Sed rhoncus facilisis purus, at accumsan simply free text available purus sagittis vitae. Nullam acelit at eros imperdiet. Pellentesque sit.
Can the 3-in-1 colored plaster solution be used in combination with other finishing materials or coatings?
Sed rhoncus facilisis purus, at accumsan simply free text available purus sagittis vitae. Nullam acelit at eros imperdiet. Pellentesque sit.
Can the 3-in-1 colored plaster solution be used on both new construction projects and existing surfaces?
Sed rhoncus facilisis purus, at accumsan simply free text available purus sagittis vitae. Nullam acelit at eros imperdiet. Pellentesque sit.
Are there any specific maintenance or care instructions for surfaces coated with the 3-in-1 colored plaster solution?
Sed rhoncus facilisis purus, at accumsan simply free text available purus sagittis vitae. Nullam acelit at eros imperdiet. Pellentesque sit.
